Husqvarna 380BTS is a powerful commercial back pack blower with tube mounted throttle control. Large air flow and high air speed are provided by an efficient fan design together with the powerful X-Torq® engine. Commercial grade air filter gives long operating time and trouble free use. The harness has wide shoulder straps and hip belt for best ergonomics.# 71.9 cm³ / 4.4 cu.inch 50 mm / 1.97 inch 36.6 mm / 1.44 inch 3.3 kW / 4.43 hp(I) Maximum recommended engine speed 2.13 lit / 72.02 fl oz For more details or for full specification’s on this machine click here to visit husqvarna’s website. Blower / Vac TypeOther than the motor, virtually all leaf blowers are made the same way. The motor turns a fan which blows high velocity air out of a tube. This air stream can be directed wherever the operator wants. It will blow leaves, cobwebs, standing water and even snow, cleaning or clearing the area of any debris or hazard. Every leaf blower is powered by a small engine, so all are subject to the same problems when starting or running.

Always use fresh gasoline at all times, and if your leaf blower is a 2 cycle engine, make sure the mix is fresh too. If your gas is a season old, it needs to be drained and replaced with fresh fuel. Attempt to start it with fresh gas after the carburetor has been primed. This may fix the problem immediately. If you have fresh gas, prime the carburetor per the manufacturer's directions, and pull the cord a few times. The blower motor should at least fire or 'pop,' and, if it doesn't, that generally means the spark plug is bad. Although spark plugs can be cleaned, they are so inexpensive that it is better to just replace them, and eliminate them as a potential cause of the problem. Other things to check are fuel shut off valves, which if turned off, won't allow any fuel to get to the carburetor; the throttle, which needs to move into the choke position initially, or your blower won't start; and the emergency shut off handle or button, which needs to be grasped and/or pressed down or the blower won't start.

Lastly, check the wire on the spark plug to make sure it is secure and tight.isafe backpack If you have done everything above, but the engine still will not start, try removing the spark plug, and placing a teaspoon of gas directly into the cylinder. backpack ayosditoScrew the plug back in, pull the starter, and if the engine fires up but runs only briefly, the carburetor is to blame.deglingos backpack canada If you are handy at doing things yourself, purchase a carburetor rebuild kit to solve this problem. cullman backpack tripodOtherwise, the engine will need to be taken into your local small engine repair person to be rebuilt.backpack upgrade zombiu

One other carburetor problem can occur. amioko backpackIf the engine runs at first but then leaks gasoline out of the exhaust when not running, you have a needle valve that isn't sealing properly. Once again, the carb will have to be rebuilt, but until that time and to stop the leaking, simply open the gas cap and allow the pressure to be released each time you use the leaf blower. Hobby Talk: Stihl leaf blower leaking gas M&D Mower: Small engine repair Leaf blowers propel leaves and other lawn debris through the air by creating winds of up to 180 miles per hour. Most gas leaf blowers use a mixture of gas and two-cycle oil. If you mix too much oil with the gas, you... Stihl USA Inc. is a major manufacturer of outdoor power equipment. The company's product line includes devices such as trimmers, industrial demolition... Stihl is best known for its chain saws, but the company also produces a line of two-cycle power tools, including backpack blowers....

The pull cord on a Stihl gas blower cranks and starts the engine. To use it, wind it onto the recoil mechanism... The primer function on the BR600 backpack blower from Stihl exists to help bring fuel into the carburetor before the engine starts... Many problems can cause your Stihl chain saw to stop starting. These problems range widely in complexity and costliness. A leaf blower operates with a small, internal combustion engine, which only requires three basic things to start and run. Leaf blowers commonly use a two-stroke internal combustion engine. These engines have very specific fuel requirements for their operation. Stihl was established in 1926 by Andreas Stihl and has grown to become an international manufacturer of chainsaws, blowers and other outdoor... How to Make a Vertical Clay Pot Garden How to Troubleshoot a Two-Cycle Leaf Blower That Will Not Start Stihl BG 55 Handheld Blower Troubleshooting How to Test a Stihl Ignition Coil

How to Replace the Starter Rope & Rewind Spring on a Stihl Blower How to Pull Start a Leaf Blower How to Prime & Choke a Leaf BlowerThe requested URL /index.php?option=com_content&view=featured&Itemid=679 was not found on this server. Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.What is the correct fuel mixture to use with my 2 cycle engine RYOBI Outdoor Product? Your 2-cycle engine requires pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean gas container. DO NOT mix quantities larger than usable in a 30-day period. Do not use automotive lubricant or 2-cycle outboard lubricant. We recommend using a RYOBI/Homelite premium 2-cycle oil or a PowerCare 2-cycle oil. Clean surface around fuel cap to prevent contamination Loosen fuel cap slowly. Rest the cap on a clean surface. Carefully pour fuel into the tank. Prior to replacing the fuel cap, clean around the gasket.

Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage Note: it is normal for smoke to be emitted from a new engine after fist use. How do you installing the vacuum bag on the blower? Remove the nozzle and upper blower tube from the blower by twisting and removing from the blower housing outlet Unzip the vacuum bag and push the vacuum bag adaptor through the opening opposite the zipper as shown Make sure the wider end of the adaptor remains on the inside of the vacuum bag when installed properly Align the raised slots on the vacuum bag adaptor with the raised locking tabs on the blower housing outlet Push the vacuum bag adaptor onto the housing and twist to lock into place Rotate the vacuum bag until the shoulder strap is upright Make sure the vacuum bag is zipped and closed before starting the unit How do you installing the vacuum tubes on the blower? Secure the upper and lower vacuum tubes together by aligning the raised locking tabs with the raised slots

Tap the tube assembly on ground until the screw holes in the lower tube are in the raised slot of the upper tube and then secure with the supplied screws. Then depress door tab using a flathead screwdriver and open the vacuum inlet door After you open the inlet door, align the screw mounts on vacuum opening with screws on Turning the screws clockwise, to tighten and secure the upper vacuum tube to the blower housing How do you remove the vacuum tubes on the blower? First, Loosen screws of the upper vacuum tube by turning them counterclockwise Then, remove the vacuum tube assembly from the blower housing Close the vacuum inlet cover door securely How do you fill the fuel tank on the blower? Clean the surface around the fuel cap to prevent contamination Loosen the fuel cap slowly by turning it counterclockwise Pour the fuel mixture carefully into the tank. Clean and inspect the fuel cap gasket before replacing the fuel cap Replace the fuel cap and tighten it by turning it clockwise

Wipe spilled fuel from the product and move at least 30 ft. away from the refueling area before starting the product. NOTE: It is normal for smoke to be emitted from a new engine during first use Warning: Always shut off engine before fueling and never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke and stay away from open flames and sparks. Failure to safely handle fuel could result in serious personal injury. What is the right mixture of fuel to fill the blower up? This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean container approved for gasoline. DO NOT mix quantities larger than usable in a 30-day period. NOTE: We recommend you use Homelite premium 2-cycle lubricant, PowerCare 2-cycle lubricant (6.4 oz. or 16 oz.), or an equivalent high-quality synthetic 2-cycle lubricant in this product.

Mix at 2.6 oz. per gallon (US). Do not use automotive lubricant or 2-cycle outboard lubricant. How do I start the blower? The blower should be on a flat, bare surface for starting. Slowly press the primer bulb 10 times NOTE: After the 10th press, fuel should be visible in the primer bulb. If it is not, continue to press the primer until you see fuel in the bulb. Set the choke lever to the FULL CHOKE position Lock cruise control lever/throttle lock Pull the starter grip and rope sharply until engine attempts to run. Do not pull the starter grip more than four (4) times Set the choke lever to the HALF CHOKE position and then pull the starter grip and rope until the engine runs NOTE: If the engine does not start, return to the FULL CHOKE position and repeat the steps that follow Allow the engine to run for 15 seconds, then set the choke lever to the RUN position How do I stop the blower? To stop the engine, depress and hold the stop switch to the stop position “ ”.

How do I restart my engine when it’s hot? Set the choke lever to the RUN position. Lock cruise control lever/throttle lock. Pull the starter grip and rope until the engine runs. How do I use the cruise control lever/throttle lock on the blower? The cruise control lever/throttle lock can be used to operate the blower without holding the throttle trigger To engage, pull cruise control lever/throttle lock back towards yourself, and stop at the desired throttle setting To release, push cruise control lever/throttle lock all the way towards the front of unit. How do I CLEAN THE AIR FILTER on the blower? Remove the air filter cover by turning the dial counterclockwise while gently pulling on the cover Rinse filter with clean water and gently squeeze the filter until excess water is removed Place the air filter cover back on the unit and then turn dial clockwise until cover is secure How do I store the blower? Clean all foreign material from the product and store the idle unit indoors in a dry, well-ventilated area that is inaccessible to children.